MACHINES AND MECHANISMS

Automation of maintenance and diagnostics processes for equipment at road machinery manufacturing enterprises

Authors

How to cite

GOST Chalenko T. A. Automation of maintenance and diagnostics processes for equipment at road machinery manufacturing enterprises // STROITEL'NYE I DOROZHNYE MASHINY. 2026. Vol. 70. No. 10. P. 83-94. DOI: 10.25726/q2073-7030-6657-h
APA Chalenko, T. A. (2026). Automation of maintenance and diagnostics processes for equipment at road machinery manufacturing enterprises. STROITEL'NYE I DOROZHNYE MASHINY, 70(10), 83-94. https://doi.org/10.25726/q2073-7030-6657-h

Abstract

Production equipment at road machinery plants is serviced under the planned preventive maintenance system, and automated condition monitoring is proposed as its replacement. Published estimates of the benefit come from particular machine fleets and do not separate the roles of detection probability, false alarms and inspection interval. The study uses a scenario model to ask how the availability of a production equipment unit changes when maintenance switches to automated monitoring, and at which diagnostic parameters this advantage disappears. A scenario model was built: a Monte Carlo simulation based on the delay-time (P–F interval) concept, with 10,000 replications of a model unit-year under common random numbers for run-to-failure, planned preventive maintenance with inspections, and automated monitoring. Sensitivity to 13 parameters was examined and the simulation was checked against analytical values. The computed availability was 99.41% for run-to-failure, 99.19% for inspections every 336 h and 99.62% for monitoring. Monitoring prevented 78.9% of failures, whereas inspections prevented 19.3%. Monitoring outperformed the better of the two alternatives when its detection probability exceeded 0.286 and its false alarm rate stayed below 3.14 per 1,000 h. Within the model, the effect of automation depends not on the presence of sensors as such but on the ratio of the inspection interval to the P–F interval, on detection probability and on the number of false alarms. When inspections are spaced more widely than the defect development interval, planned maintenance yields lower availability than run-to-failure.

Keywords

road machinery manufacturing maintenance technical diagnostics automated condition monitoring P–F interval availability Monte Carlo method false alarms

Funding

The authors did not declare any external funding for this research.

References

Govorkov A., Gladkikh V., Perelygin V., Strelkov A. Predictive maintenance as a tool for sustainable development of mining enterprises // Sustainable Development of Mountain Territories. 2026. vol. 18. no. 3. pp. 1600-1613.

Zelentsov B.P. Formation of state-transition diagrams under technical condition monitoring // Reliability. 2022. vol. 22. no. 2. pp. 22-29.

Nemenko A.V., Nikitin M.M. Construction of optimal maintenance for a process line // Fundamental and Applied Problems of Engineering and Technology. 2021. no. 2(346). pp. 42-50.

Revenko N.F., Ivanova T.N., Mishchenkova O.V. Transformation of approaches to organizing maintenance and repair of machines and equipment. On the centenary of the planned preventive maintenance system // Bulletin of Volga State University of Technology. Series: Economics and Management. 2022. no. 2(54). pp. 35-46.

Salikhov R.F., Berdnikov I.E. Method for calculating the annual duration of maintenance and repairs for domestic and foreign excavators as operating time accumulates // Bulletin of SibADI. 2024. vol. 21. no. 1. pp. 26-37.

Salikhov R.F., Permyakov V.B. Study of the influence of technical parameter dynamics on the operational productivity of hydraulic single-bucket excavators // Bulletin of SibADI. 2024. vol. 21. no. 4. pp. 540-560.

Simonov A. Selection of the recommended frequency for monitoring the technical condition of components and parts of gas-dynamic equipment based on statistical failure data // Automation and Modeling in Design and Management. 2026. no. 3. pp. 78-85.

Titaryov D.V., Krivtsanov S.O. Analysis and justification of the choice of architecture for a software complex for repair and maintenance management for service companies // Control Systems and Information Technologies. 2021. no. 1 (83). pp. 90-95.

Tolstykh L.P., Gora S.M., Medvedev N.K., Medvedev V.K. On organizing maintenance and repair of an enterprise's machine tool fleet in the “condition-based” format // Machine Tool and Instrument. 2024. no. 2 (35). pp. 70-74.

Tugengold A.K., Voloshin R.N., Yusupov A.R., Kruglova T.N. Maintenance of process machines through digitalization // Bulletin of Don State Technical University. 2019. vol. 19. no. 1. pp. 74-80.

Churanov S.A., Tumanov A.A., Kandlin M.A. How to ensure reliable operation of metalworking machine tool spindles and reduce the costs of their maintenance and repair // Machine Tool and Instrument. 2025. no. 2 (39). pp. 76-82.

Shtyrkin F.A., Lukyanov N.D. Application of artificial neural networks to predict failures of haul trucks // Reliability. 2026. vol. 26. no. 3. pp. 3-9.

Andersen J.F., Nielsen B.F. A comparative study of time-based maintenance and condition-based maintenance for multi-component systems // Reliability Engineering and System Safety. 2025. Vol. 256. Art. 110759.

Jodejko-Pietruczuk A., Werbińska-Wojciechowska S. Development and sensitivity analysis of a technical object inspection model based on the delay-time concept use // Maintenance and Reliability. 2017. Vol. 19. no. 3. pp. 403-412.

Shen G., Zeng W., Zhang Y., Han C., Liu P. Determination of the average maintenance time of CNC machine tools based on type II failure correlation // Maintenance and Reliability. 2017. Vol. 19. no. 4. pp. 604-614.

Issue

Section

MACHINES AND MECHANISMS

Metrics

7 views
0 downloads
Want to publish with us?
Submit an article

Similar Articles

1 2 3 4 > >> 

You may also start an advanced similarity search for this article.